Pennsylvania Code & Bulletin
COMMONWEALTH OF PENNSYLVANIA

• No statutes or acts will be found at this website.

The Pennsylvania Bulletin website includes the following: Rulemakings by State agencies; Proposed Rulemakings by State agencies; State agency notices; the Governor’s Proclamations and Executive Orders; Actions by the General Assembly; and Statewide and local court rules.

PA Bulletin, Doc. No. 12-1417a

[42 Pa.B. 4724]
[Saturday, July 28, 2012]

[Continued from previous Web Page]

LAND RECYCLING AND ENVIRONMENTAL REMEDIATION

UNDER ACT 2, 1995

PREAMBLE 1


Acknowledgment of Notices of Intent to Remediate Submitted under the Land Recycling and Environmental Remediation Standards Act (35 P. S. §§ 6026.101—6026.907)

 Sections 302—305 of the Land Recycling and Environmental Remediation Standards Act (act) (35 P. S. §§ 6026.302—6026.305) require the Department to publish in the Pennsylvania Bulletin an acknowledgment noting receipt of Notices of Intent to Remediate. An acknowledgment of the receipt of a Notice of Intent to Remediate is used to identify a site where a person proposes to, or has been required to, respond to a release of a regulated substance at a site. A person intending to use the background standard, Statewide health standard, the site-specific standard or intend to remediate a site as a special industrial area shall file a Notice of Intent to Remediate with the Department. A Notice of Intent to Remediate filed with the Department provides a brief description of the location of the site, a list of known or suspected contaminants at the site, the proposed remediation measures for the site and a description of the intended future use of the site. A person who demonstrates attainment of one or a combination of cleanup standards or receives approval of a special industrial area remediation identified under the act will be relieved of further liability for the remediation of the site for contamination identified in reports submitted to and approved by the Department. Furthermore, the person shall not be subject to citizen suits or other contribution actions brought by responsible persons not participating in the remediation.

 Under sections 304(n)(1)(ii) and 305(c)(2) of the act, there is a 30-day public and municipal comment period for sites proposed for remediation using a site-specific standard, in whole or in part, and for sites remediated as a special industrial area. This period begins when a summary of the Notice of Intent to Remediate is published in a newspaper of general circulation in the area of the site. For the following site, proposed for remediation to a site-specific standard or as a special industrial area, the municipality, within which the site is located, may request to be involved in the development of the remediation and reuse plans for the site if the request is made within 30 days of the date specified as follows. During this comment period, the municipality may request that the person identified as the remediator of the site develop and implement a public involvement plan. Requests to be involved and comments should be directed to the remediator of the site.

 For further information concerning the content of a Notice of Intent to Remediate, contact the environmental cleanup program manager in the Department regional office listed before the notice. If information concerning this acknowledgment is required in an alternative form, contact the community relations coordinator at the appropriate regional office. TDD users may telephone the Department through the AT&T Relay Service at (800) 654-5984.

 The Department has received the following Notices of Intent to Remediate:

Northeast Region:  Eric Supey, Environmental Cleanup and Brownfields Program Manager, 2 Public Square, Wilkes-Barre, PA 18701-1915.

Penn's Best, 7318 State Route 6, Meshoppen and Washington Townships, Wyoming County. Chuck Orloski, EPS of Vermont, Inc., 850 West Oak Street, Old Forge, PA 18518 has submitted a Notice of Intent to Remediate on behalf of his client, Penn's Best Incorporated, PO Box 128, Meshoppen, PA 18630, concerning the remediation of soil found to have been impacted by No. 2 fuel oil as a result of a release, which occurred during the delivery of fuel oil to an unregulated 275 gallon aboveground storage tank. The applicant proposes to remediate the site to meet the Non-Residential Statewide Health Standard for soil. It is anticipated that the subject property will continue to be used as a trucking warehouse, distribution and logistics facility. A summary of the Notice of Intent to Remediate was expected to be published in the New Age Examiner on July 11, 2012.

DETERMINATION OF APPLICABILITY FOR RESIDUAL WASTE GENERAL PERMITS


Application(s) for Determination of Applicability received Under the Solid Waste Management Act (35 P. S. §§ 6018.101—6018.1003); the Municipal Waste Planning, Recycling and Waste Reduction Act (53 P. S. §§ 4000.101—4000.1904); and Residual Waste Regulations for a General Permit to Operate Residual Waste Processing Facilities and/or the Beneficial Use of Residual Waste Other Than Coal Ash

Northeast Region: Regional Solid Waste Manager, 2 Public Square, Wilkes-Barre, PA 18711-0790

General Permit Application No. WMGR096, Program I.D. WMGR028NE003, Wayco Incorporated, 1500 Purdytown Pike, Hawley, PA 18428. A General Permit Determination of Applicability (DOA) for the beneficial use of asphalt plant baghouse fines as a soil additive located in Palmyra Township, Wayne County. The application for Determination of Applicability was received in the Regional Office on July 2, 2012, and was deemed administratively complete as of July 17, 2012.

 Persons interested in obtaining more information about the Determination of Applicability application may contact William Tomayko, Environmental Program Manager, Waste Management Program, Northeast Regional Office, 2 Public Square, Wilkes-Barre, PA 18711-0790 at 570-826-2511. TDD users may contact the Department through the Pennsylvania Relay service, (800) 654-5984.

 Public comments must be submitted within 30 days of the publication of this notice, and these comments may recommend revisions to, and approval or denial of the application.

OPERATE WASTE PROCESSING OR DISPOSAL AREA OR SITE


Application(s) received Under the Solid Waste Management Act, the Municipal Waste Planning, Recycling and Waste Reduction Act and Regulations to Operate Solid Waste Processing or Disposal Area or Site.

Northeast Region: Regional Solid Waste Manager, 2 Public Square, Wilkes-Barre, PA 18701-1915

Permit Application No. 101371. McAuliffe Hauling and Recycling Services, Inc., 4816 Timberline Road, Walnutport, PA 18088. A permit renewal application for the continued operation of this municipal solid waste transfer station located in Lehigh Township, Northampton County. The application was received in the Regional Office on June 20, 2012, and was found to be administratively complete as of July 11, 2012.

 Comments concerning the application should be directed to William Tomayko, Environmental Program Manager, Waste Management Program, Northeast Regional Office, 2 Public Square, Wilkes-Barre, PA 18701-1915 at 570-826-2511. TDD users may contact the Department through the Pennsylvania Relay service, (800) 654-5984. Public comments must be submitted within 60 days of this notice and may recommend revisions to, and approval or denial of the application.

AIR QUALITY

PLAN APPROVAL AND OPERATING PERMIT APPLICATIONS NEW SOURCES AND MODIFICATIONS

 The Department has developed an ''integrated'' plan approval, State Operating Permit and Title V Operating Permit program. This integrated approach is designed to make the permitting process more efficient for the Department, the regulated community and the public. This approach allows the owner or operator of a facility to complete and submit permitting documents relevant to its application one time, affords an opportunity for public input and provides for sequential issuance of the necessary permits.

 The Department received applications for Plan Approvals or Operating Permits from the following facilities.

 Copies of these applications, subsequently prepared draft permits, review summaries and other support materials are available for review in the regional office listed before the applications. Persons interested in reviewing the application files should contact the appropriate regional office to schedule appointments.

 Persons wishing to receive a copy of a proposed Plan Approval or Operating Permit shall indicate interests to the Department regional office within 30 days of the date of this notice and shall file protests or comments on a proposed Plan Approval or Operating Permit within 30 days of the Department providing a copy of the proposed documents to persons or within 30 days of its publication in the Pennsylvania Bulletin, whichever comes first. Interested persons may also request that hearings be held concerning a proposed Plan Approval or Operating Permit. A comment or protest filed with the Department regional office shall include a concise statement of the objections to the issuance of the Plan Approval or Operating Permit and relevant facts which serve as the basis for the objections. If the Department schedules a hearing, a notice will be published in the Pennsylvania Bulletin at least 30 days prior the date of the hearing.

 Persons with a disability who wish to comment and require an auxiliary aid, service or other accommodation to participate should contact the regional office listed before the application. TDD users may contact the Department through the Pennsylvania AT&T Relay Service at (800) 654-5984.

 Final Plan Approvals and Operating Permits will contain terms and conditions to ensure that the source is constructed and operating in compliance with applicable requirements in 25 Pa. Code Chapters 121—143, the Federal Clean Air Act (42 U.S.C.A. §§ 7401—7671q) and regulations adopted under the Federal Clean Air Act.

PLAN APPROVALS


Plan Approval Applications Received under the Air Pollution Control Act (35 P. S. §§ 4001—4015) and 25 Pa. Code Chapter 127, Subchapter B that may have special public interest. These applications are in review and no decision on disposition has been reached.

Southwest Region: Air Quality Program, 400 Waterfront Drive, Pittsburgh, PA 15222-4745

Contact: M. Gorog & B. Hatch, Environmental Engineer Managers—Telephone: 412-442-4163/5226

65-01017A: Mountain Gathering, LLC (810 Houston Street, Fort Worth, TX 76102) for operation of eight (8) natural gas compressor engines at their Westmoreland Compressor Station in New Florence Borough, Westmoreland County. This is a Minor Facility Plan Approval submittal.

Northwest Region: Air Quality Program, 230 Chestnut Street, Meadville, PA 16335-3481

Contact: Edward Orris, New Source Review Chief—Telephone: 814-332-6636

10-380B: Mountain Gathering, LLC—Forward Compressor Station (810 Houston Street, Fort Worth, TX 76102) for construction of a natural gas compressor station at 910 Saxonburg Road, Butler, PA 16002, in Jefferson Township, Butler County. The compressor station will consist of eight (8) natural gas compressor engines rated at 1,775 bhp, three (3) 16,800 gallon condensate storage tanks with a flare to control VOC emissions and TEG dehydrator unit rated at 1.5 MMBtu/hr.

10-381A: Mountain Gathering, LLC—Forward Compressor Station (810 Houston Street, Fort Worth, TX 76102) for construction of a natural gas compressor station at 275 Powder Mill Road, Renfrew, PA 16053 in Forward Township, Butler County. The compressor station will consist of eight (8) natural gas compressor engines rated at 1,775 bhp, three (3) 16,800 gallon condensate storage tanks with a flare to control VOC emissions and TEG dehydrator unit rated at 1.5 MMBtu/hr.


Intent to Issue Plan Approvals and Intent to Issue or Amend Operating Permits under the Air Pollution Control Act and 25 Pa. Code Chapter 127, Subchapter B. These actions may include the administrative amendments of an associated operating permit.

Southeast Region: Air Quality Program, 2 East Main Street, Norristown, PA 19401

Contact: Sachin Shankar, New Source Review Chief—Telephone: 484-250-5920

46-0005AI: Merck, Sharp & Dohme, Corp. (770 Sunmeytown Pike, West Point, PA 19486-0004) for expansion of Building 62 disinfection operations necessary to meet product demand at an existing permitted building in Upper Gwynedd Township, Montgomery County. The plan approval is for a Title V facility. The modification will increase VOC emissions from the building, which was previously permitted as part of Source 105 in the Title V permit. The VOC emissions increase will be limited to 2.0 tons per year, resulting in total VOCs from this building being 7.08 tons/year. The plan approval will include monitoring, recordkeeping and reporting requirements designed to keep the facility operating within all applicable air quality requirements.

09-0007E: Waste Management Disposal Services of Pennsylvania, Inc. (WMDSPI) (1000 New Ford Mill Road, Morrisville, PA 19067) for installation of two (2) propane fired crystallizers of 3 MMBtu/hr and 5 MMBtu/hr rated capacity at the Geological Reclamation Operations and Waste Systems (GROWS) landfill in Falls Township, Bucks County. The crystallizers will be used within a new and upgraded leachate treatment system at the facility to reduce the aqueous volume from a reverse osmosis unit. The GROWS landfill is a Title V facility. The crystallizers will result in an increase of emissions of the following pollutants on a 12-month rolling basis: particulate matter (PM/PM10/PM2.5) 0.50 tons/year, sulfur oxides 0.60 tons/year, nitrogen oxides (NOx) 5.50 tons/year, carbon monoxide (CO) 3.00 tons/year, volatile organic compounds (VOC) 0.500 tons/year and ammonia (NH3) 13.9 tons/year. Emissions will be minimized by use of Best Available Technology (BAT) to include the design features of the combustion chambers of the crystallizers which produce high combustion efficiency and by the use of propane, a clean burning fuel. A mist eliminator will further minimize particulate emissions due to drift. The crystallizer installation is subject to the emissions offset requirements of 25 Pa. Code, Chapter 127, Subchapter E (relating to nonattainment new source review) for the aggregated emissions in the contemporaneous time period. Emissions that are required to be offset are: 29.7 tons of NOx and 25.8 tons of VOC. The Department has authorized and WMDSPI has provided the required ERCs under Plan Approval 09-0007F. Plan Approval 09-0007E will contain monitoring, recordkeeping and testing requirements designed to keep the facility operating within the allowable emissions limits and all applicable air quality requirements.

23-0001AD: Sunoco, Inc. (4th and Green Streets, Marcus Hook, PA 19061) for installation of SCR for the control of CO emissions on six (6) existing diesel-fired dewatering pumps in Marcus Hook Borough, Delaware County. The plan approval is for a Title V facility. The installation of controls for CO emissions is required under the NESHAP standard found in 40 CFR 63, Subpart ZZZZ for existing CI Engines. CO emissions are anticipated to decrease by 1.27 tons, with a similar increase in GHG emissions. NSR and PSD regulations will not be triggered with this project. The plan approval will include monitoring, recordkeeping and reporting requirements designed to keep the facility operating within all applicable air quality requirements.

Northeast Region: Air Quality Program, 2 Public Square, Wilkes-Barre, PA 18711-0790

Contact: Ray Kempa, New Source Review Chief—Telephone: 570-826-2507

58-399-029: William Field Service Co., LLC, (1605 Coraopolis Heights Road, Moon Township, PA 15108) for construction and operation of a three (3) (CAT G3612LE) Caterpillar natural gas fired compressor engines, one (1) Solar Taurus 60-7800S turbine, three (3) dehydration unit with reboiler, catalytic converter, and Enclosed Flare. The VOC emissions from the facility will not equal or exceed 50 TPY, based on a 12-month rolling sum. The NOx emissions from the facility will not equal or exceed 100 TPY, based on a 12-month rolling sum. Total PM, SOx, and CO emissions from the facility will not equal or exceed 100 TPY, based on a 12-month rolling sum. The HAPs from the facility must never equal or exceed 10 TPY of any single HAP and must never equal or exceed 25 TPY of all aggregated HAPs, based on a 12-month rolling sum at its Central Compressor Station facility in Bridgewater and Brooklyn Township, Susquehanna County. The plan approval will include all appropriate testing, monitoring, recordkeeping and reporting requirements designed to keep the operations within all applicable air quality requirements.

Southcentral Region: Air Quality Program, 909 Elmerton Avenue, Harrisburg, PA 17110

Contact: Thomas J. Hanlon, Facility Permitting Chief—Telephone: 717-705-4862 or Daniel Husted, New Source Review Chief—Telephone: 717-705-4863

67-05083C: Calpine Mid Merit LLC, York Energy Center (PO Box 6066 92 DC 72, Newark, DE 19744-6066) for a modification to an existing plan approval of a gas turbine cogen power plant, located in Peach Bottom Township, York County.

 In accordance with 25 Pa. Code §§ 127.44(a) and 127.45(a), the Department of Environmental Protection (DEP) has received and intends to issue a Plan Approval to the above mentioned company. Plan Approval No. 67-05083C will constitute a modification of Plan Approval No. 67-05083.

 Plan Approval (PA) No. 67-05083C generally addresses the following changes to Plan Approval No. 67-05083: remove 6 ppm CO emissions limit during startup/shutdown period, but retain it during other periods; delete provisions related to simple cycle operation; update CEM and stack test conditions; and clarify, and add alternative to, the ammonia slip monitoring requirements. This plan approval modification may be incorporated into the facility-wide Title V operating permit. The Plan Approval will contain emission standards, monitoring, recordkeeping and operating restrictions designed to keep the facility operating within all applicable air quality requirements. The plan approval includes the following emissions limits for the facility, based on any consecutive 12-month period:

 Nitrogen oxides—460.2 tons

 Volatile organic compounds—46.2 tons

 Carbon monoxide—439.3 tons

 Sulfur dioxide—301 tons

 Particulate matter—523.3 tons

 Sulfuric acid mist—46.1 tons

 Hazardous air pollutants (HAPs)—less than 10 tons for any single HAP or 25 tons total

 Ammonia—444.5 tons

 Copies of the application, DEP's analysis and other documents used in the evaluation of the application are available for public review during normal business hours at Air Quality Program, 909 Elmerton Avenue, Harrisburg, PA 17110. A person may oppose the proposed plan approval, or may provide the Department with additional information to consider in its review, by filing a written protest with the Department at the address listed above. Each written comment must include the name, address and telephone number of the person submitting the comments, reference number of the proposed permit, and a concise statement regarding the relevancy of the information or objections to the permit issuance.

 A 30-day comment period, from the date of publication of this notice in the Pennsylvania Bulletin, will exist for the submission of comments or protests, or for requests for a public hearing. A public hearing may be held, if the Department of Environmental Protection, in its discretion, decides that such a hearing is warranted based on the comments received.

 Daniel C. Husted, New Source Review Chief, may be contacted at 717-705-4863, or at PA DEP Air Quality Program, 909 Elmerton Avenue, Harrisburg, PA 17110, for additional information or for the submission of comments protests or requests for a public hearing.

 Plan approvals issued to sources identified in 25 Pa. Code § 127.44(b)(1)—(4) or plan approvals issued to sources with limitations on the potential to emit may become part of the SIP, and will be submitted to EPA for review and approval.

Northcentral Region:  Air Quality Program, 208 West Third Street, Williamsport, PA 17701

Contact: Muhammad Q. Zaman, Environmental Program Manager—Telephone: 570-327-3648

08-00045A: Moxie Liberty, LLC (612 Center Street South, Suite 200, Vienna, VA 22180) has submitted an application to the Pennsylvania Department of Environmental Protection for plan approval to construct a natural gas-fired combined-cycle power plant to produce 936 MW or less of electricity in Asylum Township, Bradford County. The project consists of two identical 1 x 1 power blocks, and each block includes a combustion gas turbine and a steam turbine. Each combined-cycle process will also include a heat recovery steam generator and supplemental duct burners. Additionally, one diesel-fired emergency generator, one diesel-fired fire water pump, two diesel fuel storage tanks, two lube oil storage tanks, and one aqueous ammonia storage tank were proposed to be constructed and operated. Each combined-cycle process will be rated at 468 MW or less. The heat input rating of each combustion gas turbine is 2890 MMBtu/hr (HHV) or less, and the heat input rating of each supplemental duct burner is equal to 387 MMBtu/hr (HHV) or less. This application is subject to the Prevention of Significant Deterioration (PSD) of Air Quality regulations of 40 CFR 52.21, the Nonattainment New Source Review (NNSR) regulations of 25 Pa. Code §§ 127.201—27.218, and the Best Available Technology (BAT) requirements of 25 Pa. Code §§ 127.1 and 127.12. The facility's total particulate matter (PM) including total PM10 and total PM2.5, nitrogen oxides, carbon monoxide, volatile organic compounds, and greenhouse gas emissions are subject to the PSD requirements. The facility's nitrogen oxides and volatile organic compounds emissions are also subject to the NNSR requirements. The Department has determined that the proposed levels of the air contaminants emissions satisfy best available control technology (BACT) and Lowest Achievable Emission Rate (LAER) requirements as well as the Department's BAT requirements.

 The facility is also subject to the following Standards of Performance for New Stationary Sources (NSPS): 40 CFR Part 60 Subpart KKKK—Standards of Performance for Stationary Combustion Turbines codified in 40 CFR 60.4300 through 60.4420 and 40 CFR Part 60 Subpart IIII—Standards of Performance for Stationary Compression Ignition Internal Combustion Engines codified in 40 CFR 60.4200 through 60.4219. The proposed project is also subject to the National Emission Standards for Hazardous Air Pollutants for Stationary Reciprocating Internal Combustion Engines codified 40 CFR 63.6580 through 63.6675 as applicable to the proposed diesel-fired engines. The Department has determined that this facility satisfies all applicable requirements of these subparts including Maximum Achievable Control Technology (MACT) requirements.

 Pursuant to the PSD provisions of 40 CFR 52.21 and 25 Pa. Code § 127.83, Moxie Liberty has performed dispersion modeling. The air quality analysis methodology is consistent with the ''Guideline on Air Quality Models'' codified in Appendix W to 40 CFR Part 51, associated United States Environmental Protection Agency modeling policy and guidance, and the Department's recommendations. The air quality analysis adequately demonstrates that the proposed emissions due to the project will not cause or significantly contribute to air pollution in violation of the National Ambient Air Quality Standards for carbon monoxide (CO), nitrogen dioxide (NO2), particulate matter less than 2.5 micrometers (PM-2.5), and particulate matter less than 10 micrometers (PM-10), and the PSD standards for NO2, PM-2.5, and PM-10. In addition, the analysis adequately demonstrates that the project's proposed emissions, in conjunction with anticipated emissions due to general commercial, residential, industrial, and other growth associated with the project, will not impair visibility, soils, and vegetation. Furthermore, the effect of the project's emissions on air quality related values, including visibility, in Federal Class I areas is adequately addressed.

 Based on the findings presented above, the Department intends to issue a plan approval for the proposed project. The following is a summary of the conditions that the Department proposes to place in the plan approval to be issued to ensure compliance with all applicable air quality regulatory requirements:

 1. Pursuant to the best available control technology of the Prevention of Significant Deterioration provisions in 40 CFR Section 52.21 and of 25 Pa. Code § 127.83 and the lowest achievable emission rate of the New Source Review Regulation provisions in 25 Pa. Code §§ 127.201—127.217 as well as the best available technology provisions in 25 Pa. Code §§ 127.1 and 127.12,

 (a) emissions from the operation of each combined-cycle powerblock shall not exceed the limits specified below:

 1. Carbon monoxide: 2.0 ppmdv and 15.3 lb/hr

 2. Oxides of nitrogen (as NO2): 2.0 ppmdv and 25.2 lb/hr

 3. Volatile organic compounds: 1.0 ppmdv and 3.8 lb/hr (without duct burner firing) and 1.5 ppmdv and 6.2 lb/hr (with duct burner firing)

 4. Sulfur dioxide: 0.0011 lb/MMBtu and 3.5 lb/hr

 5. Total (filterable and condensable) Particulate Matter: 0.0057 lb/MMBtu (with and without duct burner firing) and 12.1 lb/hr (without duct burner firing) and 12.8 lb/hr (with duct burner firing)

 6. Total PM10: 0.0057 lb/MMBtu (with and without duct burner firing) and 12.1 lb/hr (without duct burner firing) and 12.8 lb/hr (with duct burner firing)

 7. Total PM2.5: 0.0057 lb/MMBtu (with and without duct burner firing) and 12.1 lb/hr (without duct burner firing) and 12.8 lb/hr (with duct burner firing)

 8. H2SO4: 0.00017 lb/MMBtu and 1.5 lb/hr (with and without duct burner firing)

 9. NH3: 5 ppmdv (with and without duct burner firing) and 23.2 lb/hr (with duct burner firing) and 22.8 (without duct burner firing)

 (b) ppmdv = parts per million volume on a dry gas basis, corrected to 15 percent O2

 (c) The nitrogen oxides, carbon monoxide and ammonia emissions limits shall be established as one-hour period.

 (d) Unless otherwise specified herein, the above emissions limits shall apply at all times except for periods of startup and shutdown.

 (e) The applicable sulfur dioxide requirements in 40 CFR 60.4330 are streamlined into this permit condition.

 2. (a) The permittee shall install, certify, maintain and operate continuous emission monitoring systems (CEMS) for nitrogen oxides, carbon monoxide, carbon dioxide and ammonia emissions as well as volumetric flow on the exhaust of each combined-cycle powerblock in accordance with all applicable requirements specified in 25 Pa. Code Chapter 139 and the Department's ''Continuous Source Monitoring Manual.'' No CEMS or flow monitoring system may however be installed unless Phase I approval has first been obtained from the Department.

 (b) The permittee shall submit a Phase I application to the Department for all CEMS and flow monitoring systems to be associated with each combined-cycle powerblock at least 6 months prior to the expected startup of each respective unit.

 3. (a) Unless otherwise specified in the plan approval, the emissions limits shall apply at all times except for periods of startup and shutdown.

 (b) Startup and shutdown are defined as follows:

 (1) A cold start is defined as a restart occurring 72 hours or more after shutdown and shall not be in excess of 79 minutes in duration.

 (2) A warm start is defined as a restart occurring between 12 to 72 hours after shutdown and shall not be in excess of 68 minutes in duration.

 (3) A hot start is defined as a restart occurring less than 12 hours after shutdown and shall not be in excess of 58 minutes in duration.

 (4) Shutdown is defined as the period between the time that the combined-cycle powerblock drops below 60 percent operating level.

 (c) Shutdown shall not occur for more than 16 minutes in duration.

 (d) The permittee shall record the time, date and duration of each startup and shutdown.

 (e) The permittee shall operate the facility so as to minimize the frequency and duration of startup and shutdown events.

 (f) The permittee shall operate the Continuous Emission Monitoring Systems (CEMS) during periods of startup and shutdown.

 4. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the permittee shall monitor and keep records of the amount of fuel used each month in each of the combined-cycle powerblocks as well as the monthly heat input and hours of operation. All information to satisfy this recordkeeping requirement shall be kept for a minimum of five (5) years and shall be made available to the Department upon request.

 5. Pursuant to the best available control technology of the Prevention of Significant Deterioration provisions in 40 CFR Section 52.21 and of 25 Pa. Code § 127.83, as well as the best available technology provisions in 25 Pa. Code §§ 127.1 and 127.12, each combined-cycle powerblock shall be fired on only natural gas. The sulfur content of the natural gas shall not exceed 0.4 grains/100 scf.

 6. Pursuant to 25 Pa. Code § 127.12b, (a) the permittee shall keep accurate and comprehensive records of the following to demonstrate compliance with the fuel requirements specified above under part I. Restrictions for each combined-cycle powerblock:

 (1) The gas quality characteristics in a current, valid purchase contract, tariff sheet or transportation contract for the gaseous fuel, specifying that the maximum total sulfur content of the fuel is 0.4 grain/100 scf or less AND minimum percent methane composition equals 70% by volume or the fuel has a lower heating value between 950 and 1,100 British thermal units per standard cubic foot; OR

 (2) Representative fuel sampling data which show that the sulfur content of the gaseous fuel does not exceed 0.4 grain/100 scf AND minimum percent methane composition equals 70% by volume or the fuel has a lower heating value between 950 and 1,100 British thermal units per standard cubic foot.

 (i) With additional authority for this item taken from 40 CFR 70.6, the records of the fuel sampling performed in this paragraph shall include the following;

 (i) The date, place, and time of sampling;

 (ii) The date(s) analyses were performed;

 (iii) The company or entity that performed the analyses;

 (iv) The analytical techniques or methods used;

 (v) The results of such analyses; and

 (vi) The operating conditions as existing at the time of sampling or measurement

 (b) All information to satisfy this recordkeeping requirement shall be kept for a minimum of five (5) years and shall be made available to the Department upon request.

 7. Pursuant to the best available control technology of the Prevention of Significant Deterioration provisions in 40 CFR Section 52.21 and of 25 Pa. Code § 127.83, as well as the best available technology provisions in 25 Pa. Code §§ 127.1 and 127.12, emissions from the operation of each combined-cycle powerblock shall not exceed the limits specified below:

 a. Greenhouse Gases (as CO2e): 1,480,086 tons in any 12 consecutive month period.

 b. Hazardous Air Pollutants (HAP): 6.23 tons in any 12 consecutive month period.

 c. Hexane: 2.1 tons in any 12 consecutive month period.

 d. Formaldehyde: 1.32 tons in any 12 consecutive month period.

 8. The permittee shall conduct initial EPA reference method testing within 180 days of the startup of each combined-cycle powerblock and subsequent testing every two years from the previous tests for nitrogen oxides, carbon monoxide, ammonia slip, volatile organic compounds, sulfur oxides (SO2), sulfuric acid mist, total PM, total PM10, total PM2.5, hexane and formaldehyde as well as keep record of the monthly emissions of sulfur oxides (SO2), sulfuric acid mist, total PM, total PM10, total PM2.5, hexane and formaldehyde to demonstrate compliance with the emission limitations.

 9. The Department will evaluate the actual emission rates and may revise the allowable emission rates based upon demonstrated performance (CEMS data, stack tests results), and/or subsequently promulgated applicable requirements during the first five years of operation. Any revision of the allowable emission rates shall be accomplished by minor modification provided that the revised allowable emission rates do not exceed levels at which the lowest achievable emission rate (LAER), best available control technology (BACT) and best available technology (BAT) were evaluated, do not exceed the level at which facility impacts were modeled, and that are not a result of a physical change at the facility.

 10. Pursuant to the best available control technology of the Prevention of Significant Deterioration provisions in 40 CFR Section 52.21 and of 25 Pa. Code § 127.83, as well as the best available technology provisions in 25 Pa. Code §§ 127.1 and 127.12, the emission of visible air contaminants from the operation of each combined-cycle powerblock shall not be in excess of 10% opacity for any 3-minute block period and shall not exceed 20% at any time.

 11. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the inlet temperature, outlet temperature, and pressure differential across the SCR catalyst shall be monitored and recorded on a continuous basis. Visual and audible alarms shall be utilized to indicate improper operation.

 12. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the pre-control and post-control NOx emissions shall be monitored by the feed-forward process control loop to ensure maximum control efficiency and minimum NH3 slip.

 13. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the pressure differential across the oxidation catalyst as well as the catalyst inlet and outlet temperatures shall be monitored and recorded on a continuous basis (1-hour average). Visual and audible alarms shall be utilized to indicate improper operation. The pressure differential and temperature ranges will be established based upon the recorded data and the stack testing. In addition to these operating parameters, the CO emissions from the CEMS will be used as an indicator for VOC emission compliance based upon the recorded data and the stack testing.

 14. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, an oxygen monitor shall be in each stack to monitor oxygen levels to ensure maximum combustion efficiency. The percent oxygen in the stack associated with each combined-cycle powerblock will be established based upon the recorded data and the stack testing.

 15. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, high efficiency inlet air filters shall be used in the air inlet section of each combined-cycle powerblock.

 16. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the permittee shall monitor and record the pressure differential across the inlet air filters on a weekly basis.

 17. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, all air-contaminant sources and control devices shall be maintained and operated in a manner consistent with good air pollution control practices and in accordance with the manufacturer's recommendations.

 18. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the total combined hours of startups and shutdowns for both combined-cycle powerblocks shall not exceed 500 hours in any 12 consecutive month period.

 19. Pursuant to the best available control technology of the Prevention of Significant Deterioration provisions in 40 CFR Section 52.21 and of 25 Pa. Code §§ 127.83 and the lowest achievable emission rate of the New Source Review Regulation provisions in 25 Pa. Code §§ 127.201—127.217 as well as the best available technology provisions in 25 Pa. Code §§ 127.1 and 127.12, each combustion turbine associated with a powerblock shall be equipped with dry-low-NOx (DLN) combustors.

 20. The combustion turbines, heat recovery steam generators and duct burners associated with each combined-cycle powerblock shall comply with all applicable requirements of Subpart KKKK of the Standards of Performance for New Stationary Sources, 40 CFR 60.4300 through 60.4420 (Standards of Performance for Stationary Combustion Turbines).

 21. The permittee shall comply with all applicable SO2 monitoring requirements specified in 40 CFR Section 60.4360, 60.4365, and 60.4370.

 22. The permittee shall comply with all applicable monitoring requirements specified in 40 CFR Sections 60.4340, 60.4345, and 60.4350.

 23. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the permittee shall operate and maintain the stationary combustion turbine, air pollution control equipment, and monitoring equipment in a manner consistent with good air pollution control practices for minimizing emissions at all times including during startup, shutdown, and malfunction pursuant to 40 CFR Section 60.4333.

 24. The permittee shall comply with the applicable testing requirements specified in 40 CFR Sections 60.4400, 60.4405, and 60.4415.

 25. The permittee shall comply with the reporting requirements specified in 40 CFR Sections 60.4375 and 60.4380.

 26. Pursuant to 40 CFR 72.7, the combined-cycle powerblocks meet the criteria for new unit exemption. As specified in 40 CFR 72.7(b)(1), the powerblocks are exempt from the Acid Rain Program, except for the provisions of 40 CFR 72.2—72.7, and 72.10—72.13. The permittee shall comply with applicable sections of the Acid Rain Program.

 27. The permittee shall comply with the applicable requirements of 40 CFR Part 96 and 25 Pa. Code Chapter 145 Subchapter D.

 28. The permittee shall submit a complete NOx Budget permit application in accordance with 40 CFR Section 96.21(b)(1)(ii).

 29. The permittee shall comply with the applicable requirements of 40 CFR Part 97.

 30. The permittee shall submit a complete NOx Budget permit application in accordance with 40 CFR Section 97.21(b)(1)(ii).

 31. The permittee shall comply with the applicable Mandatory GHG Reporting requirements of 40 CFR Part 98.

 32. The facility shall comply with the requirements in 40 CFR Part 98 Subpart D, (40 CFR 98.40—98.48).

 33. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the duct burners shall only be used when the combined-cycle powerblock is required to achieve 100% load.

 34. The permittee shall construct and operate only one of the two options. The first option consists of constructing two Mitsubishi M501GAC lean premix DLN natural-gas-fired combustion turbines (CT) and steam turbines (ST), where each CT and ST train are configured in a single shaft alignment and drive one common electric generator. Each unit will be equipped with natural-gas-fired duct burners (DB) and heat recovery steam generators (HRSG). Each Mitsubishi train will be capable of producing approximately 468 megawatts (MW) of electricity. The maximum heat input rating of each CT is 2879 MMBtu/hr (high heating value, HHV) and 2600 MMBtu/hr (lower heating value, LHV). Each DB will have a maximum heat input rating of 387 MMBtu/hr (HHV) and 350 MMBtu/hr (LHV). The second option consists of constructing two Siemens SGT6-8000H lean premix DLN natural-gas-fired CTs with STs, where each CT and ST train are configured in a single shaft alignment and drive one common electric generator. Each unit will be equipped with natural-gas-fired DBs and HRSGs. Each Siemens train will be capable of producing approximately 454 MW of electricity. The maximum heat input rating of each CT is 2980 MMBtu/hr (HHV) and 2685 MMBtu/hr (LHV). Each DB will have a maximum heat input rating of 164 MMBtu/hr (HHV) and 148 MMBtu/hr (LHV).

 35. (a) Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the two combined-cycle powerblocks shall be constructed and operated from the options identified in this plan approval. The two combined-cycle powerblocks chosen by the permittee shall be either the two 468 MW combined-cycle powerblocks (P101 and P102) or the two 454 MW combined-cycle powerblocks (P103 and P104).

 (b) The Mitsubishi combined-cycle powerblocks shall not emit more than 116.7 tons of carbon monoxide in any 12 consecutive month period, 102.7 tons of nitrogen oxides in any 12 consecutive month period, 14.2 tons of sulfur dioxide in any 12 consecutive month period, 2.2 tons of sulfuric acid mist in any 12 consecutive month period, 52.5 tons of total particulate matter (PM10) including total PM10 and PM2.5 in any 12 consecutive month period, 101.6 tons of ammonia in any 12 consecutive month period, 33.8 tons of volatile organic compounds in any 12 consecutive month period, 1,480,086 tons of greenhouse gases (expressed as CO2e) in any 12 consecutive month period, 6.23 tons of hazardous air pollutants in any 12 consecutive month period, 2.1 tons of hexane in any 12 consecutive month period, 1.24 tons of formaldehyde in any 12 consecutive month period. The Mitsubishi combined-cycle powerblock option (combined with all of the other air contaminant sources) shall not emit more than 233.46 tons of carbon monoxide in any 12 consecutive month period, 206.36 tons of nitrogen oxides (as nitrogen dioxide) in any 12 consecutive month period, 67.60 tons of volatile organic compounds in any 12 consecutive month period, 2.48 tons of formaldehyde in any 12 consecutive month period, 12.46 tons of hazardous air pollutants in any 12 consecutive month period, 105.00 tons of total PM (PM/PM10/PM2.5 including condensable PM) in any 12 consecutive month period, 28.40 tons of sulfur oxides (as sulfur dioxide) in any 12 consecutive month period, 4.4 tons of sulfuric acid mist in any 12 consecutive month period and 2,960,271 tons of greenhouse gases in any 12 consecutive month period. The emissions limits specified in (b) of this condition apply at all times including during periods of startup and shutdown.

 (c) The Siemens combined-cycle powerblocks shall not emit more than 86.8 tons of carbon monoxide in any 12 consecutive month period, 100.7 tons of nitrogen oxides in any 12 consecutive month period, 13.4 tons of sulfur dioxide in any 12 consecutive month period, 2.1 tons of sulfuric acid mist in any 12 consecutive month period, 53.7 tons of total particulate matter (PM10) including total PM10 and PM2.5 in any 12 consecutive month period, 99.9 tons of ammonia in any 12 consecutive month period, 30.1 tons of volatile organic compounds in any 12 consecutive month period, 1,388,540 tons of greenhouse gases (expressed as CO2e) in any 12 consecutive month period, 5.2 tons of hazardous air pollutants in any 12 consecutive month period, 0.9 tons of hexane in any 12 consecutive month period, 1.32 tons of formaldehyde in any 12 consecutive month period. The Siemens combined-cycle powerblock option (combined with all of the other air contaminant sources) shall not emit more than 173.66 ton of carbon monoxide in any 12 consecutive month period, 202.36 tons of nitrogen oxides (as nitrogen dioxide) in any 12 consecutive month period, 60.20 tons of volatile organic compounds in any 12 consecutive month period, 2.64 tons of formaldehyde in any 12 consecutive month period, 10.40 tons of hazardous air pollutants in any 12 consecutive month period, 107.40 tons of total PM (PM/PM10/PM2.5 including condensable PM) in any 12 consecutive month period, 26.80 tons of sulfur oxides (as sulfur dioxide) in any 12 consecutive month period, 4.2 tons of sulfuric acid mist in any 12 consecutive month period and 2,777,179 tons of greenhouse gases in any 12 consecutive month period. The emissions limits specified in (c) of this condition apply at all times including during periods of startup and shutdown.

 36. Pursuant to the new source review provisions in 25 Pa. Code §§ 127.201—127.217, the permittee shall purchase and apply 237.3 tons per year of NOx emission reduction credits (ERCs) and 77.7 tons per year of VOC ERCs prior to the start of operation of Source IDs P101 and P102 at the facility to offset the total of the net increase in potential to emit. The permittee shall certify to the Northcentral Regional Office of the Department the amount of ERCs purchased, the company from which the ERCs were purchased, and the effective date of transfer of the ERCs. The purchase and application of the NOx and VOC ERCs shall be tracked in the Department's ERC registry system. Failure to purchase and apply the ERCs prior to the start of operation at the facility shall make this plan approval null and void.

 37. Pursuant to the new source review provisions in 25 Pa. Code §§ 127.201—127.217, the permittee shall purchase and apply 232.7 tons per year of NOx emission reduction credits (ERCs) and 69.2 tons per year of VOC ERCs prior to the start of operation of Source IDs P103 and P104 at the facility to offset the total of the net increase in potential to emit. The permittee shall certify to the Northcentral Regional Office of the Department the amount of ERCs purchased, the company from which the ERCs were purchased, and the effective date of transfer of the ERCs. The purchase and application of the NOx and VOC ERCs shall be tracked in the Department's ERC registry system. Failure to purchase and apply the ERCs prior to the start of operation at the facility shall make this plan approval null and void.

 38. Pursuant to the requirements of 40 CFR Section 60.4205(b) and 60.4211(c), the engine-generator associated with Source ID P105 shall be EPA certified to meet the emissions standards that are specified in 40 CFR Section 89.112 for the same model year and maximum engine power.

 39. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the visible emissions from the engine-generator associated with Source ID P105 shall not exceed 15% for any 3-minute block period and 50% at any time.

 40. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the air contaminant emissions from the exhaust of the engine-generator associated with Source ID P105 shall not exceed the following limitations:

 a. Nitrogen Oxides (expressed as NO2)—4.93 g/hp-hr, 16.02 lb/hr, 0.80 tpy

 b. Carbon Monoxide—0.13 g/hp-hr, 0.41 lb/hr, 0.02 tpy

 c. Volatile Organic Compound (expressed as THC)—0.01 g/hp-hr, 0.03 lb/hr, 0.01 tpy

 d. Particulate Matter less than 10 microns in diameter (PM10)—0.02 g/hp-hr, 0.06 lb/hr, 0.01 tpy

 e. PM2.5—0.02 g/hp-hr, 0.06 lb/hr, 0.01 tpy

 f. Sulfur Oxides (expressed as SO2)—0.01 g/hp-hr, 0.03 lb/hr, 0.01 tpy

 41. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12,

 (a) the annual cumulative hours of operation of the engine-generator associated with Source ID P105 and fire pump engine associated with Source ID P106 shall not exceed 100 hours in any 12-consecutive month period.

 (b) The duration of each readiness test associated with the engines shall be no more than 30 minutes.

 (c) There shall be no simultaneous readiness testing of the engine-generator and fire pump engine within the same hour.

 (d) There shall be no readiness testing of the engines during the startup or shutdown of the combined-cycle powerblocks

 42. Pursuant to the requirements of 40 CFR Section 60.4211(f), the operation of the engine-generator associated with Source ID P105 shall not be used for peak shaving or to generate income by supplying power to an electric grid or otherwise supply non-emergency power as part of a financial arrangement with another entity.

 43. Within 180 days of the commencement of operation of the engine-generator associated with Source ID P105, the permittee shall conduct stack tests on the exhaust of the engine-generator in order to show compliance with the best available technology emissions limitations for nitrogen oxides, carbon monoxide, and volatile organic compounds.

 44. Pursuant to 40 CFR Section 60.4206, the permittee shall operate and maintain the engine-generator associated with Source ID P105 to achieve the emission standards specified in 40 CFR Section 89.112 and 89.113 over the entire life of the engine. Any testing used to verify compliance with this work practice restriction shall be performed in accordance with 40 CFR Part 60 Subpart IIII, including 40 CFR Section 60.4212, and Department-approved test methods and procedures.

 45. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the permittee shall only use diesel fuel that is classified as ultra-low sulfur non-highway diesel fuel (15 ppm Sulfur Maximum) pursuant to 40 CFR Part 80 Subpart I, to operate the engine-generator associated with Source ID P105.

 46. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the engine-generator associated with Source ID P105 shall be equipped with a non-resettable hour meter that accurately monitors the engine-generator's hours of operation.

 47. Pursuant to 40 CFR Section 60.4210(f), the engine-generator associated with Source ID P105 shall meet the labeling requirements in Section 60.4210(f).

 48. Pursuant to 40 CFR Section 60.4211(c), the engine-generator associated with Source ID P105 shall be installed and configured according to the manufacturer's emission-related specifications.

 49. The permittee shall record the hours that the engine-generator associated with Source ID P105 operated through the non-resettable hour meter and shall calculate the 12-consecutive month total hours of operation, including supporting documentation, to verify compliance with the operational restriction specified in this permit on a monthly basis. Additionally, the permittee shall record the time of operation of the engine-generator and the reason the engine-generator was in operation during that time. The information used to demonstrate compliance with this condition shall be kept for a minimum of five years and shall be made available to the Department upon request.

 50. Pursuant to 25 Pa. Code § 127.12b, the permittee shall keep accurate and comprehensive records of the following information for the engine-generator associated with Source ID P105:

 (a) the supporting information and calculations used to demonstrate that the emissions of particulate matter and sulfur oxides from the exhaust of the engine-generator comply with the best available technology emissions limitations as well as the requirements in 25 Pa. Code §§ 123.13 and 123.21, respectively;

 (b) the stack test reports.

 51. Pursuant to 25 Pa. Code § 127.12b, the permittee shall keep record of the fuel certification reports for each delivery of diesel fuel for the engine-generator associated with Source ID P105 to verify compliance with the fuel restriction requirements for the engine-generator.

 52. The engine-generator associated with Source ID P105 is subject to the requirements in 40 CFR Part 60 Subpart IIII. The permittee shall comply with all applicable provisions specified 40 CFR Section 60.4200 through 60.4219, including appendices.

 53. Source ID P105 is a Caterpillar Model DM9933 Generator that includes a Caterpillar C32 TA, V-12, 4-stroke, water-cooled, diesel-fired reciprocating internal combustion engine (or equivalent as approved by the Department) used to supply emergency power to the site. The engine-generator shall include electronic fuel injection and a turbocharged aspiration system.

 54. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the engine-pump associated with Source ID P106 shall be EPA certified to meet the following emissions standards:

 a. Nitrogen Oxides (expressed as NO2)—2.6 g/hp-hr, 2.5 lb/hr, 0.13 tpy

 b. Carbon Monoxide—0.5 g/hp-hr, 0.51 lb/hr, 0.03 tpy

 c. Volatile Organic Compound (expressed as THC)—0.10 g/hp-hr, 0.10 lb/hr, 0.01 tpy

 d. Particulate Matter less than 10 microns in diameter (PM10)—0.09 g/hp-hr, 0.09 lb/hr, 0.01 tpy

 e. PM2.5—0.09 g/hp-hr, 0.09 lb/hr, 0.01 tpy

 f. Sulfur Oxides (expressed as SO2)—0.01 g/hp-hr, 0.01 lb/hr, 0.001 tpy

 55. Pursuant to the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the visible emissions from the engine-pump associated with Source ID P106 shall not exceed 15% for any 3-minute block period and 50% at any time.

 56. Pursuant to 40 CFR Section 60.4206, the permittee shall operate and maintain the engine-pump associated with Source ID P106 to achieve the emission standards in this permit over the entire life of the engine. Any testing used to verify compliance with this work practice restriction shall be performed in accordance with 40 CFR Part 64 Subpart IIII, including 40 CFR Section 60.4212, and Department-approved test methods and procedures.

 57. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the permittee shall only use diesel fuel that is classified as ULTRA-LOW SULFUR NON-HIGHWAY DIESEL FUEL (15 ppm Sulfur Maximum) pursuant to 40 CFR Part 80 Subpart I, to operate the engine-pump associated with Source ID P106.

 58. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the engine-pump associated with Source ID P106 shall be equipped with a non-resettable hour meter that accurately monitors the engine-pump's hours of operation.

 59. The permittee shall record the hours that the engine-pump associated with Source ID P106 operated through the non-resettable hour meter and shall calculate the 12-consecutive month total hours of operation, including supporting documentation, to verify compliance with the operational restriction specified in this permit on a monthly basis. Additionally, the permittee shall record the time of operation of the engine-generator and the reason the engine-pump was in operation during that time. The information used to demonstrate compliance with this permit condition shall be kept for a minimum of five years and shall be made available to the Department upon request.

 60. Pursuant to 25 Pa. Code § 127.12b, the permittee shall keep accurate and comprehensive records of the following information for the engine-pump associated with Source ID P106:

 (a) the supporting information and documentation used to demonstrate that the emissions from the exhaust of the engine-pump comply with the emissions limitations in this permit as well as the requirements in 25 Pa. Code §§ 123.13 and 123.21, respectively

 61. Pursuant to 25 Pa. Code § 127.12b, the permittee shall keep record of the fuel certification reports for each delivery of diesel fuel for the engine-pump associated with Source ID P106 to verify compliance with the fuel restriction requirements for the engine-pump.

 62. The engine-pump associated with Source ID P106 is subject to the requirements in 40 CFR Part 60 Subpart IIII. The permittee shall comply with all applicable provisions specified 40 CFR Section 60.4200 through 60.4219, including appendices.

 63. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, the duration of each test of the emergency generator or the fire pump will be restricted to 30 minutes.

 64. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, there will be no simultaneous testing of the emergency generator and the fire pump within the same hour.

 65. Pursuant to best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12, testing of the emergency generator or the fire pump will not occur during (within the same hour as) startup or shutdown of the combustion turbines.

 66. Source ID P106 is a Clark Model JX6H-UFADF0 that includes a John Deere Co. In-Line, 4-stroke, water-cooled, diesel-fired reciprocating internal combustion engine (or equivalent as approved by the Department) used to power the fire suppression system at the facility. The engine-pump shall include electronic fuel injection and a turbocharged aspiration system.

 67. The permittee shall not store any liquid containing volatile organic compounds (VOC) with a vapor pressure greater than 1.5 psia (10.5 kilopascals) under actual storage conditions in each storage tank associated with Source ID P107 unless each of the tanks are equipped with pressure relief valve which is maintained in good operating condition and which are set to release at no less than 0.7 psig of pressure or 0.3 psig of vacuum, or the highest possible pressure and vacuum in accordance with state or local fire codes or the National Fire Prevention Association guidelines or other national consensus standards acceptable to the Department.

 68. The permittee shall keep a record of the vapor pressure of the contents of each storage tank associated with Source ID P107 unless the respective tank is equipped with pressure relief valves that meets the requirement in this permit relating to pressure release settings. All information used to demonstrate compliance with this permit condition shall kept for minimum of five (5) years and shall be made available to the Department upon request.

 69. Source ID P107 consists of two (2) 15,000-gallon lube oil tanks and each tank services the lubing system associated with each of the electric generating units.

 All pertinent documents used in the evaluation of the application are available for public review during normal business hours at the Department's Northcentral Regional office, 208 West Third Street, Suite 101, Williamsport, PA 17701. Appointments for scheduling a review must be made by calling 570 327 3693.

 Any person(s) wishing to provide the Department with additional information, which they believe should be considered prior to the issuance of this plan approval, may submit the information to the Department of Environmental Protection at the address shown in the preceding paragraph. A 30-day comment period from the date of this publication will exist for the submission of comments. Each written comment must contain the name, address and telephone number of the person submitting the comments, identification of the proposed permit (specify Plan Approval No. 08-00045A) and a concise statement regarding the relevancy of the information or objections to issuance of the plan approval.

 A public hearing may be held, if the Department of Environmental Protection, in its discretion, decides that such a hearing is warranted based on the information received. All persons submitting comments or requesting a hearing will be notified of the decision to hold a hearing by publication in the newspaper or by the Pennsylvania Bulletin, or by telephone, where the Department of Environmental Protection determines such notification is sufficient. Written comments or requests for a public hearing should be directed to Muhammad Q. Zaman, Environmental Program Manager, Department of Environmental Protection, Air Quality Program, Northcentral Regional Office, 208 West Third Street, Suite 101, Williamsport, PA 17701, 570 327 3648.

57-00005A: Appalachia Midstream Services, LLC (P. O. Box 54382, 6100 N. Western Avenue, Oklahoma City OK 73154) has submitted an application to the Pennsylvania Department of Environmental Protection (Department) for plan approval to construct five compressor engines and one dehydration unit at their Cherry Compressor Station located in Cherry Township, Sullivan County. The respective facility is a state only (natural minor) facility for which a state only operating permit has not yet been issued.

 The Department's review of the information submitted by Appalachia Midstream Services indicates that the compressor engines to be constructed will comply with applicable regulatory requirements pertaining to air contamination sources. Additionally, the Department has determined that the proposed engines satisfy best available technology (BAT) requirements, pursuant to 25 Pa. Code §§ 127.1 and 127.12 as well as the Standards of Performance for Stationary Spark Ignition Internal Combustion Engines specified in 40 CFR 60, Subpart JJJJ. Pursuant to the requirements of BAT, the compressor engines are restricted to emit emissions for the following pollutants at a rate above; 0.50 g/Bhp-hr for nitrogen oxide (NOx), 0.19 g/Bhp-hr for carbon monoxide (CO), 0.16 g/Bhp-hr for volatile organic compounds (VOC, expressed as NMNEHC), and 0.04 g/Bhp-hr for formaldehyde. To demonstrate compliance with these limitations, Appalachia will be required to conduct EPA reference method testing on each engine-compressor's exhaust for NOx, CO, VOC, and formaldehyde emissions. Continuous compliance demonstration will include monitoring of operational parameters of the catalyst and testing for NOx and CO on an approximate quarterly basis. The compressor-engines are also required to use only pipeline quality natural gas as fuel for operation. Each engine-compressor has a site rating of 3,550 bhp.

 Based on the findings above, the Department proposes to issue a plan approval with annual emission restrictions for all sources at the Cherry Compressor Station as well as monitoring, recordkeeping and work practice requirements to verify compliance with the annual emission restrictions.

 In addition to the emission limitations above, the following is a summary of the types of conditions the Department intends to place in Plan Approval 57-00005A to ensure compliance with applicable Federal and State regulatory requirements including the best available technology requirements of 25 Pa. Code §§ 127.1 and 127.12.

 Initial and subsequent testing at the exhaust of each engine-compressors using Department-approved methods on an approximate annual basis

 Monitoring requirement to take representative samples of gas into the station, the inlet and outlet exhaust temperature of catalysts to demonstrate continuous compliance with the destruction efficiency of the catalyst and monitoring requirement on the engines-compressors for nitrogen oxide and carbon monoxide emissions on an approximate quarterly basis

 Recordkeeping requirement for engine-compressors' gas usage and operational hours including the records of all required monitoring

 Work practice requirement to construct and operate in accordance with the manufacturer's recommendations and good air pollution control practices, minimize blowdowns and limit the emission of malodors to level undetectable outside the property

 The air contaminate emissions from all sources at the proposed compressor station will be restricted to the following annual 12 consecutive month limitations; 92.4 tpy for NOx, 42.3 tpy for CO, 42.3 tpy for VOC, 1.5 tpy for sulfur oxide, 6.3 tpy for particulate matter (PM) including PM10 and PM2.5, 7.1 tpy for formaldehyde, and 22.6 tpy for hazardous air pollutants (HAP). Compliance requirements for these annual restrictions include monthly recordkeeping of emissions from each source at the proposed station

 All pertinent documents used in the evaluation of the application are available for public review during normal business hours at the Department's Northcentral Regional office. Any person(s) wishing to provide the Department with additional information, which they believe should be considered prior to the issuance of this plan approval, may submit the information to the Department of Environmental Protection at the address shown in the preceding paragraph. A 30-day comment period from the date of this publication will exist for the submission of comments. Each written comment must contain the name, address and telephone number of the person submitting the comments, identification of the proposed permit (specify Plan Approval No. 57-00005A) and a concise statement regarding the relevancy of the information or objections to issuance of the plan approval.

 All persons requesting additional information or submitting comments should be directed to Muhammad Q. Zaman, Environmental Program Manager, Department of Environmental Protection, Air Quality Program, Northcentral Regional Office, 208 West Third Street, Suite 101, Williamsport, PA 17701, 570 327 3648.

Northwest Region: Air Quality Program, 230 Chestnut Street, Meadville, PA 16335-3481

Contact: Edward Orris, New Source Review Chief—Telephone: 814-332-6636

25-1025A: Erie Cemetery Association (2116 Chestnut Street, Erie, PA 16502), the Department intends to issue a plan approval for authorization to continue operation of two existing crematories at their existing facility in the City of Erie, Erie County. Public notice is required for sources required to obtain a Plan Approval in accordance with 25 Pa. Code § 127.44.

 The identical crematories were installed in 1959 and 1975. Erie Cemetery Association (ECA) was unaware that they should have received authorization for the crematory built in 1975. The units' operation has never resulted in a complaint to the Department or ECA. This plan approval issuance is subject to the following special conditions:

 Work Practice

 1) The crematories' burners shall be operated and maintained as prescribed by the manufacturer. A copy of the burner's operational and maintenance literature shall be maintained onsite with the units at all times.

 2) The owner/operator may only cremate human remains and the container used to transport the remains.

 3) The owner/operator of the crematory must ensure that all medical devices (e.g. pacemakers, defibrillators, etc.) and potentially hazardous remedial devices (e.g. radioactive implants, etc.) have been removed from bodies and properly disposed of prior to cremation. Documentation certifying compliance with this requirement shall be maintained for each cremation.

 4) The crematory shall be:

 a. Operated in such a manner as not to cause air pollution, as defined in 25 Pa. Code § 121.1.

 b. Operated and maintained in a manner consistent with good operating and maintenance practices.

 c. Attended by a trained operator at all times when the unit is in operation.

 d. Operated and maintained in accordance with the manufacturer's specifications and the applicable terms and conditions of this Permit.

 e. Operated such that the temperature at the exit of the secondary chamber shall be maintained at or above 1600° F throughout the cremation cycle.

 f. Observed by a trained operator for stack emissions. The permittee shall verify compliance with visible and odor emission limitations through the following procedures:

 i. The permittee shall observe the exhaust stack of the crematory at least once during each cremation cycle for the presence of visible emissions;

 ii. If any visible or odor emissions are apparent, the permittee shall take immediate action to eliminate them; and

 iii. If any visible or odor emissions are apparent after the corrective action, the crematory shall not start another cremation cycle until the permittee can verify compliance with the visible emission limitations specified in this plan approval through methods prescribed in 25 Pa. Code § 123.43 (relating to measuring techniques), such as Method 9 readings taken by a certified visible emissions reader.

 iv. At a minimum of once during any consecutive six month period, visible stack emissions shall be measured by an individual certified in method 9 visible emission evaluation. The observations shall begin during initial firing of the primary chamber and shall occur for a minimum of 30 minutes with averages taken in 3 minute intervals. A record of this evaluation shall be kept on site in a log and shall include (at a minimum) the name, title, and signature of the observer, documentation of certification, the date, time, temperature, description of atmospheric conditions, and the approximate weight of material to be cremated. Erie Cemetery Association may petition the Department for a reduced frequency of these visible emission evaluations after four compliant observations have been made in succession.

 g. If nighttime operation of the crematory is to occur, adequate artificial lighting of the plume at the stack outlet must be provided to enable observations of stack emissions at night.

 Monitoring

 The owner/operator shall install, maintain, and operate continuous temperature monitors to measure the temperatures at the exit from the primary combustion chamber and at the exit from the secondary (or last) chamber of the crematory. Sensors shall be located such that flames from the burners do not impinge on the sensors. These temperatures shall be recorded in either analog or digital read-only format.

 Recordkeeping

 The owner/operator shall maintain records of:

 i. Visible emission observations and any corrective actions;

 ii. A time and corresponding temperature during each cremation cycle when the temperature of the secondary (or last) combustion chamber achieves 1600°F or greater.

 iii. The number of cremations performed;

 iv. Operating training certification(s);

 v. Burner adjustments and maintenance;

 vi. Thermocouple calibrations, adjustments and replacements;

 vii. The removal from the body and proper disposal of any implanted electronic devices and potentially hazardous remedial devices

 Emission Restrictions

 1) No person may permit the emission to the outdoor atmosphere of particulate matter from any incinerator, at any time, in such a manner that the particulate matter concentration in the effluent gas exceeds 0.1 grain per dry standard cubic foot, corrected to 12% carbon dioxide. (Filterable Only)

 2) Visible emissions shall not exceed either of the following limitations:

 i. Equal to or greater than 20% for a period or periods aggregating more than three minutes in any 1 hour;

 ii. Equal to or greater than 40% at any time.

 3) [25 Pa. Code § 123.31] A person may not permit the emission into the outdoor atmosphere of any malodorous air contaminants from any source in such a manner that the malodors are detectable outside the property of the person on whose land the source is being operated.

 In accordance with 25 Pa. Code § 127.44(e)(1), all the pertinent documents regarding this application (applications, review memos, and draft approvals) are also available for review from 8:00 a.m. to 4:00 p.m. at the Meadville Regional DEP office (Air Quality). Appointments for scheduling a review must be made by calling the DEP (814) 332-6340.

 In accordance with 25 Pa. Code § 127.44(e)(2), a 30-day comment period, from the date of publication, will exist for the submission of comments. Any person(s) wishing to provide DEP with additional information, which they believe should be considered prior to the issuance of this permit, may submit the information to Regional Air Quality Program Manager, Pennsylvania Department of Environmental Protection, 230 Chestnut Street, Meadville, PA 16335-3494 and must contain the name, address and telephone number of the person submitting the comments, identification of the proposed plan approval [25-197E] and a concise statement regarding the relevancy of the information or objections to the issuance of the permit.

 A public hearing may be held, if the Department of Environmental Protection, in its discretion, decides that such a hearing is warranted based on the comments received. All persons submitting comments or requesting a hearing will be notified of the decision to hold a hearing by publication in the newspaper or the Pennsylvania Bulletin or by telephone, where DEP determines such notification is sufficient. Written comments or requests for a public hearing should be directed to Jacob G. Chemsak, 230 Chestnut St., Meadville, PA 16335; Phone (814) 332-6638.

 In accordance with 25 Pa. Code § 127.45, a person may oppose the proposed plan approval by filing a written protest with the Department's Northwest Region.

62-141G: National Fuel Gas Supply Corp. (PO Box 2081, Erie, PA 16512), for the installation of two (2) 840 bhp natural gas compressor engines, as a replacement for four (4) existing natural gas compressor engines at their Roystone Compressor Station facility in Sheffield Township, Warren County. This is a Title V facility.

 Notice is hereby given pursuant to 25 Pa. Code §§ 127.44(b) and 127.424(b), that the Pennsylvania Department of Environmental Protection (DEP) intends to issue Plan Approval 62-141G to National Fuel Gas Supply Corp. for the installation of two (2) 840 bhp natural gas fired compressor engines, with associated NSCR catalysts at their Roystone Compressor Station facility in Sheffield Township, Warren County. These engines will replace four (4) existing engines (Source IDs 139, 140, 141, 142). The Plan Approval will subsequently be incorporated into the facility's Operating Permit through an administrative amendment in accordance with 25 Pa. Code § 127.450.

 Plan Approval No. 62-141G is for the installation of two (2) 840 bhp natural gas fired compressor engines, with associated NSCR catalysts. These engines will replace four (4) existing engines (Source IDs 139, 140, 141, 142). Based on the information provided by the applicant and DEP's own analysis, the proposed sources will each have the potential to emit approximately 2.0 tons of carbon monoxide, 4.1 tons of nitrogen oxides (NOx), and 1.5 tons of volatile organic compounds (VOCs) per year.

 The Plan Approval will contain additional testing, monitoring, recordkeeping and work practice requirements designed to keep the facility operating within all applicable air quality requirements. Copies of the application, DEP's analysis, and other documents used in the evaluation are available for public inspection between the hours of 8 a.m. and 4 p.m. weekdays at the address shown below. To make an appointment, contact Records Management at 814-332-6340.

 Anyone wishing to provide DEP with additional information they believe should be considered may submit the information to the address shown below. Comments must be received by the Department within 30 days of the last day of publication. Written comments should include the name, address, and telephone number of the person submitting comments, identification of the proposed Plan Approval; No. 62-141G and a concise statement regarding the relevancy of the information or any objections to issuance of the Plan Approval.

 A public hearing may be held, if the Department of Environmental Protection, in its discretion, decides that such a hearing is warranted on the comments received during the public comment period. All persons submitting comments or requesting a hearing will be notified of the decision to hold a hearing by publication in a local newspaper of general circulation or the Pennsylvania Bulletin or by telephone, where the Department determines such notification is sufficient. Written comments or requests for a public hearing should be directed to John Guth, Regional Air Quality Manager, Department of Environmental Protection, Northwest Regional Office, 230 Chestnut St., Meadville, PA 16335, 814-332-6940.

Department of Public Health, Air Management Services: 321 University Avenue, Philadelphia, PA 19104

Contact: Edward Wiener, Chief—Telephone: 215-685-9426

AMS 12151: Philadelphian Condominium (2401 Pennsylvania Avenue, Philadelphia, PA 19130) to install Thirteen (13) combustion units less than 8 MMBTU/hr firing either natural gas or No. 2 oil in the City of Philadelphia, Philadelphia County. The Facility will be limited to less than 25 tons of Nitrogen Oxides (NOx) emissions per year. The plan approval will contain operating, testing, monitoring, recordkeeping, and reporting requirements to ensure operation within all applicable requirements.

[Continued on next Web Page]



No part of the information on this site may be reproduced for profit or sold for profit.

This material has been drawn directly from the official Pennsylvania Bulletin full text database. Due to the limitations of HTML or differences in display capabilities of different browsers, this version may differ slightly from the official printed version.